How To Make An Acoustic Guitar Bridge

  • More than 20 Years Woodworking Experience
  • 7 Woodworking Books Available on Amazon
  • Over 1 Million Words Published About Woodworking
  • Bachelor of Arts Degree from Arizona State University
Buy My Books on Amazon

I receive Commissions for Purchases Made Through the Links in This Post.

If you want to learn how to make an acoustic guitar bridge, this guide will show you the best series of steps. Making a bridge requires several different processes. Some are easier to perform than others.

If You Like My Posts, You'll Love My Books

See My Woodworking Books Here

My process gets the most difficult phases of construction out of the way in the beginning. This reduces anxiety for the beginner, and ensures a bridge wont be ruined right at the last minute.

Making a Bridge and Selecting the Wood

how to make an acoustic guitar bridgeThe first step in how to make an acoustic guitar bridge is to select the wood. Most guitars have Rosewood or Ebony bridges.

When making a bridge by hand, almost any species of wood can be used as long as it is dense and strong. Also, select a saddle for the project, as the slot will be routed to match.

The dimensions of the bridge blank and the saddle will vary. Most acoustic guitars have similar size bridges, though there are some that will have different sizes. This is a standard acoustic guitar bridge, with a basic shape.

You can select the type of bridge that you make, and these steps will still work. as long as you are making a fixed bridge for an acoustic guitar top, these instructions will work really well.

Free Woodworking Tips Every Monday

Add Me to the List!

For a first bridge, this classic shape is perfect. The amount of carving will be less, and the construction process as a whole will be easier.

See Also: 10 Important Questions to Ask Yourself Before Making an Acoustic Guitar

Routing the Saddle Slot First

how to make an acoustic guitar bridgeOne of the more difficult steps is routing the slot for the saddle. A simple jig can be made for the Dremel tool that holds the bridge in place.

An angled board is screwed to the top of the jig, making a fence. The angle is set the same as the angle of the saddle slot, and the Dremel makes the cut.

Notice that the bridge blank is held parallel to the left edge of the jig. The fence (purple heart) is angled. This creates a slot in the bridge that is also angled. Almost all acoustic guitar saddles are angled slightly to compensate for the string being pressed.

The lower strings end up with a lightly longer scale length, maintaining the proper notes for the majority of the neck.

how to make an acoustic guitar bridgeUsing a Dremel or a router, create the slot. The best cutter for this is a spiral down cut bit, though any spiral bit will also work.

The bits I have in the shop were from a tool maker, so they are carbide. They were designed for use on metal, so the wood cuts very easily.

Free Woodworking Tips Every Monday

Add Me to the List!

Making the jig is a simple matter of drilling two holes in the bridge blank, one at each end of the saddle slot. Set the fence so that it makes contact with the edge of the router plate in both positions.

When set like this, the router will make a nice slot. If several bridges of different styles are going to be made, allowing the fence to be adjustable can help. In this case, I make the same bridge for the vast majority of my guitars, so this has a fixed fence.

See Also: 13 Helpful Tips on Making an Acoustic Guitar Bridge

Drilling the Bridge Pins

how to make an acoustic guitar bridgeAfter the slot is routed to the proper depth, typically within about 1/8″ to 1/16″ from the bottom of the bridge, the bridge pins are drilled.

This is the second most difficult thing to get right. Drilling six holes perfectly can be a challenge, but my Bridge Pin Drilling Guide solves this problem.

Place the guide on top of the bridge and position it for the holes. Take a little extra time to line it up well. Then, clamp it down to the bench or a scrap of wood for drilling.

If You Like My Posts, You'll Love My Books

See My Woodworking Books Here

It is worth making the bridge pin drilling guide, because you only need to get the holes perfect one time. After that, the guide ensures they are perfect on every bridge you make.

how to make an acoustic guitar bridgeDrill the holes using a 3/16″ bit. Make sure to drill as perpendicular as possible. A drill press is the best for this operation, but it can be done by hand as well.

Most bridge pins require a 3/6″ starting hole. Then, the holes are tapered with a reamer. The reamer creates a hole that fits the bridge pins with a taper.

This taper creates friction, and keeps the bridge pins in place. If the pins were cylindrical, they would not hold as well. This would lead to pins popping out, and strings coming off the guitar. The guide helps keep the holes aligned well, and will keep them in the proper positions.

See Also: The Biggest Thing I Wish Someone Told Me About Making an Acoustic Guitar

Drawing the Shape and Carving

how to make an acoustic guitar bridgeRemove the guide and take a look at the blank. The holes should be centered behind the saddle slot.

Once these two aspects of how to make an acoustic guitar bridge are completed, the rest of the build is easy in comparison.

At this point, draw out some guidelines for the shape and the carve. Make marks for the shape that can be followed on the band saw. Then, make marks for tapering the wings.

Free Woodworking Tips Every Monday

Add Me to the List!

The more marks that are made on the bridge as a reference, the easier the carving and shaping process will be. Check the marks, and make sure they are symmetrical. Once satisfied, begin sawing and carving out the shape.

See Also: You Can Make an Acoustic Guitar

The point of how to make an acoustic guitar bridge with my method is to get the hardest parts of the build out of the way first. Once these processes are completed, the rest of the build is easier, and less stressful.

how to make an acoustic guitar bridgeThe initial cuts can be made on a band saw. After that, a belt sander does a great job at removing material. Be careful when using the belt sander. E

specially if this is the first time carving a bridge. The belt sander can remove material quickly, so it is better to look more frequently.

Remove the bulk of the material on the belt sander, or by hand with a file. Keep in mind that the more even looking the wings are at this stage, the better over all the bridge will look. Work on the wings, and stop often to look at the symmetry.

Spend a little extra time here, and the bridge will look amazing on the guitar for a very long time.

how to make an acoustic guitar bridgeAfter the initial shaping, the bridge can be final sanded. Blend in any sharp areas, and refine the shape. Make sure that you address any scratches and tool marks.

Spend time looking at the bridge in a glancing light. This will reveal any scratches that are difficult to see.

Sand the bridge down to 220 grit, making sure that the last several passes are made with the grain. Sanding with the grain does not eliminate scratches, however it does line them up with the grain, making them less visible.

My Woodworking Tip of The Week deals with sanding, and how to minimize the effort and time it takes to final sand a project before finishing.

Finishing the bridge can be done with the same finish as the final guitar, or it can be buffed on a wheel. The Beall Wood Buff System is what I use to polish my bridges. I also have finished several with Tru-Oil and my Finishing with Tru-Oil article explains how to do it.

Tips and Tricks for Making an Acoustic Guitar Bridge

Here are some tips and tricks that can help you make a better bridge:

If You Like My Posts, You'll Love My Books

See My Woodworking Books Here

  • Even though you have to make it, an acoustic guitar bridge is not much more complicated than a simple electric guitar bridge. It’s actually easier to make this simple bridge than to set up tremolo bridges with a whammy bar. 
  • The body of the guitar, body shape, and soundhole position have an effect on how well your guitar performs, so make sure to follow your directions when making a bridge so you know it all will work together.
  • Follow the direction step by step and don’t skip any steps. This set of directions is designed to get you through the hardest parts first, and it will get easier as you go.
  • Glue the bridge to the guitar top carefully after you make it, and you will be happy you decided to make your own bridge instead of buy it.

After you know how to make an acoustic guitar bridge, you can apply this same construction style to other aspects of guitar making. Do the most difficult steps first when possible, then proceed to the easier steps.

acoustic guitar making book coverI explain this technique in my book Acoustic Guitar Making: How to make Tools, Templates, and Jigs

, as well as over 50 other tools and jigs.

This will save the beginning guitar maker a lot of money collecting the tools and jigs they need. Tooling up for making a guitar is one of the beginner hurtles that you need to get over to make a guitar.

This book lowers the entry fee for many of those tools and jigs, because you can just make them yourself.

With over 500 pages and 1600 images, it takes the mystery out of the process for beginning guitar makers. The amount of information inside the book is amazing, and you can always find something that is helpful as you flip through the pages.

Do you have any tips on how to make an acoustic guitar bridge? Share them by leaving a comment and we can all benefit from your experience.

Post Author-

  • More than 20 Years Woodworking Experience
  • 7 Woodworking Books Available on Amazon
  • Over 1 Million Words Published About Woodworking
  • Bachelor of Arts Degree from Arizona State University
Buy My Books on Amazon

I receive Commissions for Purchases Made Through the Links in This Post.

 

You Can Find My Books on Amazon!

woodworking and guitar making books
 

Filter:AllOpenResolvedClosedUnanswered
Forum Guidelines (Please Read)
ClosedWestfarthing Woodworks asked 7 months ago • 
917 views0 answers0 votes
Fretboard Jig Depth Stop
AnsweredWestfarthing Woodworks answered 3 months ago • 
596 views1 answers0 votes
Steel Wool and Vinegar Ukulele
AnsweredWestfarthing Woodworks answered 5 months ago • 
565 views1 answers0 votes
Building a Bass – What to Use for Painting the Body
AnsweredWestfarthing Woodworks answered 6 months ago • 
594 views1 answers0 votes
Tone Wood?
AnsweredWestfarthing Woodworks answered 6 months ago • 
556 views1 answers0 votes
Should I make a Kit First?
AnsweredBrian answered 6 months ago • 
420 views1 answers0 votes
Could DIY guitars built from kits sell?
AnsweredBrian answered 6 months ago • 
707 views1 answers0 votes
How can I build my own guitar?
AnsweredBrian answered 7 months ago • 
380 views1 answers0 votes
How do acoustic guitars work?
AnsweredBrian answered 7 months ago • 
437 views1 answers0 votes
What tools does someone need to build electric guitars?
AnsweredBrian answered 7 months ago • 
318 views1 answers0 votes
What types of bone are guitar saddles made from?
AnsweredBrian answered 7 months ago • 
397 views1 answers0 votes
Where do You Get Guitar Making Wood?
AnsweredBrian answered 7 months ago • 
430 views1 answers0 votes
Do You Need a Lot of Tools to Make a Guitar?
AnsweredWestfarthing Woodworks answered 7 months ago • 
361 views1 answers0 votes
Is it Hard to Make a Guitar?
AnsweredWestfarthing Woodworks answered 7 months ago • 
295 views1 answers0 votes
Does Tru-Oil Change the Tone of Your Instrument?
AnsweredWestfarthing Woodworks answered 7 months ago • 
400 views1 answers0 votes
Can You Make Your Own Guitar Making Tools?
AnsweredWestfarthing Woodworks answered 7 months ago • 
340 views1 answers0 votes
Easy Finishes for Guitars?
AnsweredWestfarthing Woodworks answered 7 months ago • 
345 views1 answers0 votes
Headstock Relief Angle?
AnsweredWestfarthing Woodworks answered 7 months ago • 
341 views1 answers0 votes
Building the Fretboard Off the Neck?
AnsweredWestfarthing Woodworks answered 7 months ago • 
361 views1 answers0 votes
Finishing a Guitar With the Bridge and Neck Separate?
AnsweredWestfarthing Woodworks answered 7 months ago • 
265 views1 answers0 votes
Carbon Fiber and No Truss Rod?
AnsweredWestfarthing Woodworks answered 7 months ago • 
361 views1 answers0 votes

An Exclusive Member of Mediavine Home

Westfarthing Woodworks LLC is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.