Make Your Own Binding Strips

brian forbes westfarthing woodworks author biography about me experience

Binding strips are expensive. A single strip can sometimes cost as much as a board big enough to make a dozen strips in the shop. Making these yourself is not difficult, and you can make your own binding strips following these instructions.

How to Make Binding Strips for Acoustic Guitars

make your own binding stripsThe first step in how to make your own binding strips is to select the wood. Choose something that has a good track record for bending. Then, find a nice flat sawn piece. It is important that the piece be flat sawn. The strips are going to be ripped from the edge of the board, so in effect they will be quarter sawn to the direction of the bends.

Select a flat sawn 4/4 piece of wood in the species you want to work with. Make sure that it is at least 36″ long, which will be enough to make binding strips. Check the wood. Make sure that it is free of defects, and well dried.

Once you have the board, split it open down the edge. If you started with a board that is 4″ wide, 36″ long, and 4/4 thick, you will now have two boards that are 4″ wide, 36″ long, and a little over 1/4″ thick. These two plates can now be sent through the thickness planer to bring them down to 1/4″ exactly.

Make your own binding strips. You will have more choice, and you can create a more custom instrument.

make your own binding stripsOnce the two boards are ready, rip them into strips that are about 3/32″ thick. To make your own binding strips well, you will need a fine tooth blade for the table saw. Install the blade, and set the fence for the cut.

Carefully rip strips from the board until it becomes too skinny to safely rip more. Switch to the other board, and rip strips from the edge until it too becomes too skinny.

Collect your strips, and discard any that did not make it through the table saw well. If a piece has dings on the ends, they can usually be cut off and there will be enough remaining to use. Typically, the fine blade will leave the strips smooth on the faces, so they will require no additional sanding.

(You may want to Make Your Own Fret Dots too.)

Almost any wood species can be used for binding strips. Most woods are easy to bend at this thickness. Making your own binding strips gives you the ability to use whatever binding you like. This allows you to choose what you want for your guitar rather than choose something from what a supplier has available.

If you have any questions on how to Make Your Own Binding Strips, please leave a comment and I will answer them. Happy building.

Post Author-

brian forbes westfarthing woodworks llc owner

  • 20 Years Experience in Woodworking
  • 7 Published Books Available on Amazon
  • 750+ Helpful Posts Written
  • 1 Million+ Words Published
 

You Can Find My Books on Amazon!

woodworking and guitar making books
 

Filter:AllOpenResolvedClosedUnanswered
Forum Guidelines (Please Read)
ClosedWestfarthing Woodworks asked 4 months ago • 
454 views0 answers0 votes
Fretboard Jig Depth Stop
AnsweredWestfarthing Woodworks answered 3 weeks ago • 
171 views1 answers0 votes
Steel Wool and Vinegar Ukulele
AnsweredWestfarthing Woodworks answered 3 months ago • 
293 views1 answers0 votes
Building a Bass – What to Use for Painting the Body
AnsweredWestfarthing Woodworks answered 3 months ago • 
276 views1 answers0 votes
Tone Wood?
AnsweredWestfarthing Woodworks answered 3 months ago • 
375 views1 answers0 votes
Should I make a Kit First?
AnsweredBrian answered 4 months ago • 
269 views1 answers0 votes
Could DIY guitars built from kits sell?
AnsweredBrian answered 4 months ago • 
485 views1 answers0 votes
How can I build my own guitar?
AnsweredBrian answered 4 months ago • 
242 views1 answers0 votes
How do acoustic guitars work?
AnsweredBrian answered 4 months ago • 
307 views1 answers0 votes
What tools does someone need to build electric guitars?
AnsweredBrian answered 4 months ago • 
228 views1 answers0 votes
What types of bone are guitar saddles made from?
AnsweredBrian answered 4 months ago • 
265 views1 answers0 votes
Where do You Get Guitar Making Wood?
AnsweredBrian answered 4 months ago • 
292 views1 answers0 votes
Do You Need a Lot of Tools to Make a Guitar?
AnsweredWestfarthing Woodworks answered 4 months ago • 
249 views1 answers0 votes
Is it Hard to Make a Guitar?
AnsweredWestfarthing Woodworks answered 4 months ago • 
204 views1 answers0 votes
Does Tru-Oil Change the Tone of Your Instrument?
AnsweredWestfarthing Woodworks answered 4 months ago • 
260 views1 answers0 votes
Can You Make Your Own Guitar Making Tools?
AnsweredWestfarthing Woodworks answered 4 months ago • 
223 views1 answers0 votes
Easy Finishes for Guitars?
AnsweredWestfarthing Woodworks answered 4 months ago • 
228 views1 answers0 votes
Headstock Relief Angle?
AnsweredWestfarthing Woodworks answered 4 months ago • 
230 views1 answers0 votes
Building the Fretboard Off the Neck?
AnsweredWestfarthing Woodworks answered 4 months ago • 
246 views1 answers0 votes
Finishing a Guitar With the Bridge and Neck Separate?
AnsweredWestfarthing Woodworks answered 4 months ago • 
170 views1 answers0 votes
Carbon Fiber and No Truss Rod?
AnsweredWestfarthing Woodworks answered 4 months ago • 
247 views1 answers0 votes

An Exclusive Member of Mediavine Home

Westfarthing Woodworks LLC is a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.